|
A U.S. wall outlet should be distributing how many volts to the Power Supply?
| ( | A | ) | | 110 Volts DC |
 |
| ( | B | ) | | 200-240 Volts DC |
|
| ( | C | ) | | 104-130 Volts DC |
|
| ( | D | ) | | 200-240 Volts AC |
|
| ( | E | ) | | 104-130 Volts AC |
The Correct Answer is: E
The most chosen answer was [ B ] :: [ 200-240 Volts DC ]
Explanation:
A properly functioning wall outlet will give off between 104-130 Volts of AC power.
Which control signal on a serial cable, indicates that the data set is ready?
(this question provided by simulationexams.com)
| ( | A | ) | | DTR |
|
| ( | B | ) | | DSR |
|
| ( | C | ) | | RTS |
|
| ( | D | ) | | CTS |
|
| ( | E | ) | | None of the above |
The Correct Answer is: B
Explanation:
COM1, COM2 on a computer uses a serial cable. The pin
assignments are shown below. The computer acts as a DTE (Data Terminal Equipment)
and the Modem acts as DCE (Data Communication Equipment).
Signal--Name---------DB9 Pin
RX------Received Data--2
TX------Transmitted Data-3
DTR-----Data Terminal Ready--4
GND---- Ground--5
DSR---- Data Set Ready--6
RTS---- Request to Send--7
CTS---- Clear to send--8
Normally, a DTE device connects to a DCE device
with a straight cable. If you want to connect two DTR devices, as you would do
to hook up two computers via the serial line to exchange files, the cable itself
must have cross connections. Such a cable is called a null modem cable.
Recognizing software:
| ( | A | ) | | Windows 3.1 |
|
| ( | B | ) | | Windows Explorer |
|
| ( | C | ) | | DOS Command Prompt |
|
| ( | D | ) | | Control Panel |
|
| ( | E | ) | | BIOS Setup Utility |
The Correct Answer is: C
Explanation:
The screen capture is a window displaying the Command Prompt in DOS.
On an Ethernet 10BaseT network what is the maximum data speed that can be carried through a CAT 5 cable?
| ( | A | ) | | 100 megabits/second |
|
| ( | B | ) | | 80 megabits/second |
|
| ( | C | ) | | 20 megabits/second |
|
| ( | D | ) | | 16 megabits/second |
|
| ( | E | ) | | 4 megabits/second |
The Correct Answer is: A
Explanation:
CAT 5 cable can carry data at a maximum speed of 100 megabits/second.
CAT 4: 20 megabits/second
CAT 3: 16 megabits/second
CAT 2: 4 megabits/second
CAT 1 wire is used with standard telephone lines inside a home.
You have loaded Windows 3.1 into the primary partition on your computer, and made it the default Operating System. You have formatted one of the logical drives in the Extended partition. Which file system would have been installed?
(this question provided by simulationexams.com)
| ( | A | ) | | FAT16 |
|
| ( | B | ) | | FAT32 |
|
| ( | C | ) | | VFAT |
|
| ( | D | ) | | NTFS |
|
| ( | E | ) | | None of the above |
The Correct Answer is: A
Explanation:
-
DOS natively supports only FAT16.
-
Since Windows 3.1 runs on top of DOS, it will also support only FAT16
file system.
-
FAT32 is supported by Windows 98 and Windows 95 OEM Release 2.
-
Note that Windows NT does not support FAT32. NT supports only FAT16 and
NTFS.
Windows 2000 supports FAT16, FAT32, and NTFS
This quiz was generated by user guest255849 in nov2002.
a+ certification || gmat test prep || pool game || funny joke
|
